Sunday, September 13, 2026

Stan Meyer's Steam Resonator — Gerbers, BOM and PCB | Stanley Meyer Open Hardware

Stan Meyer's Steam Resonator

Stan Meyer's Steam Resonator

Steam Resonator & EPG boards sit at the thermal/EM end of the Meyer replica stack: instead of driving a wet-cell or a VIC transformer, they drive a resonant stage tuned around phase-change and particle-generator behavior. This is the family builders reach for when the project moves past plasma/electrolysis-style cells into steam-phase experimentation.

This listing is Version 1 of the Steam Resonator board — the baseline circuit before the Teensy-driven Version 2 rework. Treat it as the reference design: it documents the original discrete resonator topology and driver arrangement that Version 2 will replace with a microcontroller-timed drive signal, so it's worth pulling the Version 1 gerbers even if you plan to build V2, purely to see what the MCU rework is standing in for.

Order the bare board to bench-test the resonator stage on its own before integrating it with a GMS control card or VIC front end. As with the rest of the library, this is published as documentation of the replica circuit — not as a claim about output performance — so budget your own instrumented wall-plug-in vs. output measurement if that's part of your build log.

Order the bare board direct from PCBWay: https://www.pcbway.com/project/shareproject/Stan_Meyer_s_Steam_Resonator.html
Manuals, kits and assembled hardware — Secure Supplies shop: https://www.patreon.com/c/securesupplies/shop
Schematics, build support and the full library: https://www.patreon.com/c/securesupplies

Wednesday, September 9, 2026

DROP BEAR SPEEDUINO V1 FILES ADDED — Gerbers, BOM and PCB | Stanley Meyer Open Hardware

DROP BEAR SPEEDUINO V1   FILES ADDED

DROP BEAR SPEEDUINO V1 FILES ADDED

ECU / Speeduino / Hydrogen Hot Rod — Drop Bear is the next-generation controller — the board intended to replace both the Stanley Meyer GMS gas management unit and the ECU/EMS in a single Teensy-based platform.

The stated goal on the project page is to advance the Drop Bear to UNO Q and dual Teensy. In practice that means moving off the Arduino Mega's 8-bit core onto a Teensy 3.5, 3.6 or 4.1 as the primary controller, which gives you the clock speed and the hardware timers to run injection, ignition and cell gating from one board without the sequencing compromises the Mega forces.

The power section is specified for automotive abuse rather than bench use: a resettable polyfuse on the input, reverse-polarity protection by diode or MOSFET, a 12V to 5V/3.3V DC-DC buck rather than a linear regulator, 100uF 35V bulk capacitance and a full decoupling set close to every IC and regulator. TVS diodes go on the power rails and the exposed I/O, with series-resistor-plus-TVS protection on each ADC pin.

The I/O side is built per channel: level shifting or buffering on the cam, crank and hall inputs; MOSFET or IGBT drivers with dedicated gate driver ICs for each ignition and injector channel; fast-recovery flyback diodes on every inductive load. Sensor inputs get op-amp or level-shifter conditioning where the source impedance demands it. Everything exits on waterproof automotive connectors.

The files are on the project page. This is the most ambitious board in the library and the one to build if you intend to run gas management and engine management as one integrated system rather than two boxes talking over a harness.


Get this board

Order the bare board direct from PCBWay: https://www.pcbway.com/project/shareproject/DROP_BEAR_SPEEDUINO_V1_4260e213.html

Manuals, kits and assembled hardware — Secure Supplies shop: https://www.patreon.com/c/securesupplies/shop

Schematics, build support and the full library: https://www.patreon.com/c/securesupplies

Category: ECU / Speeduino / Hydrogen Hot Rod · Tags: Stanley Meyer, Water Fuel Cell, Hydrogen Hot Rod, PCBWay, ECU / Speeduino / Hydrogen Hot Rod

Tuesday, September 8, 2026

Speeduino EFI Shield Mega 2560 Pro Rev 1.4a By Don — Gerbers, BOM and PCB | Stanley Meyer Open Hardware

Speeduino EFI Shield Mega 2560 Pro Rev 1.4a  By Don

Speeduino EFI Shield Mega 2560 Pro Rev 1.4a By Don

ECU / Speeduino / Hydrogen Hot Rod — This is the engine-management layer of the Hydrogen Hot Rod stack — the board that turns an Arduino Mega into a real, sequential, closed-loop ECU capable of running a hydrogen or dual-fuel engine.

Rev 1.4a is a later revision than the one originally published on PCBWay. It adds an on-board barometric sensor option and jumper points that let you configure the injector driver section for either two or four channels, so the same PCB covers a 4-cylinder sequential build and a smaller batch-fire setup without cutting traces.

The driver section is built around four IRL3705Z logic-level MOSFETs for the injectors with an IRF5305 P-channel device on the high side, and each channel is protected with 1.5KE36CA TVS diodes against the inductive kick you get from low-impedance injectors. Two resettable polyfuses (RXEF090 on the main feed, RXEF050 on the sensor rail) and a 22V MOV on the input keep a wiring fault from taking the Mega with it — worth respecting, because hydrogen builds tend to see more harness rework than a petrol conversion.

Everything leaves the board on a single DB37 connector, which is the standard Speeduino harness interface and keeps the ECU swappable between test mule and vehicle. Sensor inputs are conditioned with 10k pull-ups and 100R series resistors on the ADC lines; the 22uH inductor and the 0.001uF filter bank on the analogue front end are there to keep ignition noise out of the MAP and CLT readings, which is the usual failure mode when this board is mounted in the engine bay rather than the cabin.

Order the bare PCB from PCBWay and populate from the Digi-Key BOM published on the project page. If you are running this alongside a GMS gas management card, the Speeduino handles fuel and spark and the GMS handles the cell — do not try to make one board do both.


Get this board

Order the bare board direct from PCBWay: https://www.pcbway.com/project/shareproject/Speeduino_EFI_Shield_Mega_2560_Pro_Rev_1_4a__By_Don.html

Manuals, kits and assembled hardware — Secure Supplies shop: https://www.patreon.com/c/securesupplies/shop

Schematics, build support and the full library: https://www.patreon.com/c/securesupplies

Category: ECU / Speeduino / Hydrogen Hot Rod · Tags: Stanley Meyer, Water Fuel Cell, Hydrogen Hot Rod, PCBWay, ECU / Speeduino / Hydrogen Hot Rod

Thursday, June 25, 2015

HHo Video #hho #video

HHo Video

HHo Video Welcome we started this blog to post HHo Video  info

we have websites with diy section for you here
www.securesupplies.biz